Copyright © 2022 by TTMC. All rights reserved. Welding Machine Supply Johor, Puchong, Kuala Lumpur (KL), Selangor, Malaysia
 
 
| Cancel
Hypertherm
Our Products
For Welding & Cutting
Mobile :: Sub Masthead :: Products & Brands
Lincoln Ranger® 305 D Engine Driven Welder (Kubota®)

Lincoln Ranger® 305 D Engine Driven Welder (Kubota®)

Product Description

Features

  • Simple Controls - Keep training time to a minimum with the straightforward control panel of the Ranger® 305 D. The flip-down control panel door keeps less frequently used controls out of the way.
  • Single, full-range output control dial. No confusion with taps and controls!
  • 4 welding modes: CC-Stick, Downhill Pipe, CV-Wire, and DC Touch Start TIG®.
  • Dual digital output meters for presetting weld amps for stick, TIG or downhill pipe modes, or voltage for CV wire mode. Also displays actual outputs while welding. Memory feature holds output readings for 7 seconds after welding stops for viewing by the operator.
  • Output at welding terminals controlled by electronic contactor. Can be switched to “On”, or to “Remotely Controlled”.
  • Remote is auto-activated when plugged into a 6-pin connector. For the CC-stick, downhill pipe and Touch Start TIG® modes, the machine output dial becomes a maximum current limit for more fine tuning with the remote control dial or Amptrol™.
  • Compatible with many Lincoln wire feeders including the LN-25 Ironworker™, LN-15, LF-72, LF-74, LN-7 GMA, LN-742, LN-8 wire feeders and Magnum® SG Spool Gun.
  • Wire feed voltmeter switch matches polarity of wire feeder volt meter to polarity of electrode.
  • Top-of-the-line water-cooled Kubota® 18.8 HP D722 diesel engine with electric start. EPA Tier 4 Final.
  • Fully enclosed case for equipment protection and low noise. Noise at rated load:
    – 104.2 dB sound power (Lwa)
    – 80.6 dBA sound level at 23 ft. (7 m)
  • Glow plugs for rapid starting down to 5°F (-15°C).
  • Mechanical fuel pump is activated when glow plug button is pressed
 

Specification:

Machine Specifications
Product Name Ranger 305 D (Kubota)
Ordering Informaion K1727-4
Description 300 Amp DC Multi-Process Arc Welder with Lincoln Electric Chopper Technology®
10,000 Watts Peak
9,500 Watts Continuous AC Power
CC/ Pipe Rated Output (1) Current/ Voltage/ Duty Cycle DC Constant Current
305A/ 29V/ 100% 20 - 305A
DC Pipe Current
300A/ 29V/ 100% 40 - 300A
Touch Start TIG®
250A/ 30V/ 100% 20 - 250A
Single Dial Continuous Control
60V DC Max OCV @ 3650RPM
CV-Rated Output Current/ Voltage/ Duty Cycle DC Constant Voltage (2) 300A/ 29V/ 100%
14 - 29V Single-Dial Continuous Control
Wire Feeder Power 42V, 60 Hz, 15 Amps 120V, 60 Hz, 20 Amps
Generator AC Power (3)(4) 10,000 Watts Peak
9,500 Watts Continuous 60 Hz
Single Phase
Full KVA
Receptacle
40A@ 240V
40A@ 120V ea.
Branch Circuit (5)
Four 120V GFCI
Receptacles
20A per Duplex
40A Total (5)
Dimensions H x W x L inches (mm) 29.9 x 21.5 x 52.3in (759 x 546 x 1327mm)
To top of exhaust tube: 35.8in. (909mm)
Weight lbs. (kg) 698 (317)
Engine Specifications
Engine Model Kubota D722 Diesel (6) EPA Tier 4 Final
Description 3 Cylinder, 4 Cycle, Water-Cooled, Diesel Engine, Electric Fuel Pump, Auto Air-Bleed System
Horsepower & Displacement 18.8 HP @ 3600 RPM, 43.9 cu in (789 cc)
Ignition Electric Start, 12V Group 58 Battery, 550 Cold Cranking Amps, Pushbutton Start Switch, Charging Indicator
Capacities FUEL: 12 Gals (45 Ltrs)
OIL: 3.4 Qts (3.2 Ltrs)
COOLANT: 3.9 Qts (3.6 Ltrs)
Operating Speeds FULL LOAD
3,500 RPM (300A)
HIGH IDLE
3,650 RPM
LOW IDLE
2,450 RPM
Fuel Consumption 1.2 Gals/Hr
4.5 Ltr/Hr.
0.5 Gals/Hr
2.1 Ltr/Hr
0.3 Gals/Hr
1.1 Ltr/Hr
 
  1. High Altitude: For maximum rating, derate the output 2.5% to 3.5% for every 1,000 ft. (300 m). High Temperature: For maximum rating, derate 2 volts for every 18°F (10°C) above 104°F (40°C). See Operator Manual for additional information.
  2. DC constant voltage capability provides convenience and added safety when welding in electrically hazardous conditions.
  3. When welding, available auxiliary power will be reduced. Output voltage is within +\- 10% at all loads up to rated capacity.
  4. 120V will operate either 60 Hz or 50/60 Hz power tools, lights, etc.
  5. Circuits cannot be wired in parallel to operate the same device.
  6. Engine warranted separately by engine manufacturer.
 

Frequently Purchase Together

Desktop View | Mobile View
Copyright © 2022 by TTMC. All rights reserved. Welding Machine Supply Johor, Puchong, Kuala Lumpur (KL), Selangor, Malaysia
Google Site Search